aluminum electrolytic capacitors u 1 z 2 r 3 1 4 c 5 1 6 0 7 0 8 m 9 c 10 l 11 1 12 g 13 b 14 configuration taping code capacitance tolerance ( 20%) rated capacitance (10 f) rated voltage (16v) series name type plastic platform series capacitance voltage (c : 16v) lot no. positive negative x2 10c zr 0.3 max. 3.90 +0.05 0.2 d 0.5 b 0.2 c 0.2 0.5 max. a 0.3 a 0.3 e 0.5 to 0.8 zr series 3.95mml max. chip type chip type type numbering system (example : 16v 10 f) specifications zr zs dimensions 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 220 0r1 r22 r33 r47 010 2r2 3r3 4r7 100 220 330 470 101 221 4 4 5 6.3 28 33 56 96 4 5 5 6.3 28 37 45 70 5 5 6.3 33 41 52 4 5 6.3 6.3 23 37 49 58 4 5 6.3 6.3 16 27 42 52 4 5 6.3 18 29 46 4 4 4 4 4 4 4 5 6.3 1.0 2.0 2.8 4.0 8.4 13 17 20 33 rated ripple 4 0g 6.3 0j 10 1a 16 1c 25 1e 35 1v 50 1h v code rated ripple current (marms) at 85 c 120hz d a b c e 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 6.3 2.4 6.6 6.6 2.2 (mm) cap. ( f) smaller smaller stability at low temperature resistance to soldering heat z 40 c / z+20 c category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tangent of loss angle (tan ) marking performance characteristics item 40 to +85 c 4 to 50v 0.1 to 220f 20% at 120hz, 20 c after 2 minutes' application of rated voltage , leakage current is not more than 0.01 cv or 3 (a) , whichever is greater. rated voltage (v) rated voltage (v) tan ( max.) 4 0.50 4 7 15 6.3 0.30 6.3 4 8 10 0.24 10 3 8 16 0.19 16 2 4 25 0.16 25 2 4 35 0.14 35 2 3 50 0.14 50 2 3 120hz 20 c 120hz impedance ratio zt / z20 (max.) z 25 c / z+20 c after storing the capacitors under no load at 85 c for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20 c, they shall meet the specified values for the endurance characteristics listed above. the capacitors are kept on a hot plate for 30 seconds, which is maintained at 250 c. the capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20 c. black print on the case top. shelf life endurance the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 1000 hours at 85 c. capacitance change leakage current tan within 10% of the initial capacitance value less than or equal to the initial specified value less than or equal to the initial specified value capacitance change leakage current tan within 30% of the initial capacitance value 300% or less than the initial specified value less than or equal to the initial specified value chip type with 3.95mmlmax height. designed for surface mounting on high density pc board. applicable to automatic mounting machine fed with carrier tape. compliant to the rohs directive (2002/95/ec). zd voltage v 4 6.3 10 16 25 35 50 code g j a c e v h case size d (mm) taping specifications are given in page 23. recommended land size soldering by reflow are given in page 18,19. please refer to page 3 for the minimum order quantity. frequency coefficient of rated ripple current coefficient frequency 50 hz 120 hz 300 hz 1 khz 10 khz or more 0.70 1.00 1.17 1.36 1.50 cat.8100y
|
